Puttying is a necessary procedure for decoration, which can make the uneven areas of the wall base level smooth and smooth, and can also effectively prevent external moisture from corroding the wall. It is an important step in the treatment of the base level. Today, we will talk about the seven key points of applying putty powder in Jinan.
1. Measure before puttying
刮膩?zhàn)邮┕で埃枰扔贸咦觼磉M(jìn)行測量,看看墻面是否水平,以便于確定刮膩?zhàn)拥姆绞健9文佔右话闶┕杀榧纯桑粌H讓墻面更加平整,而且能將底色覆蓋掉。如果墻面不平整的地方,則涂刮多遍膩?zhàn)觼磉M(jìn)行找平處理,但每道膩?zhàn)邮┕らg隔應在兩三小時,確保墻面充分干燥。
Before puttying, measure with a ruler to see if the wall is horizontal, so as to determine the method of puttying. Putty is generally applied twice, which not only makes the wall more flat, but also covers the background color. If the wall surface is uneven, apply putty for several times for leveling, but the construction interval of each putty shall be two or three hours to ensure that the wall surface is fully dry.
2、膩?zhàn)臃凼┕ば枳龌鶎犹幚?/div>
2. Base course treatment is required for putty powder construction
檢查基面及基層清理,包括清除墻面砂灰結塊、浮砂及塵土,以提高膩?zhàn)臃鄣氖┕っ婊鶎拥钠秸群透街Γ_保基面無污染,無空鼓,無縫隙,無疏松無掉粉現象。
Check the cleaning of the base surface and base course, including the removal of sand and ash caking, floating sand and dust on the wall, to improve the flatness and adhesion of the base course of the putty powder construction surface, and ensure that the base surface is free of pollution, hollowing, cracks, looseness and powder loss.
3、施工溫度要在5℃以上
3. The construction temperature shall be above 5 ℃
施工環境一直都是非常重要的因素,如果環境溫度過低,容易影響到膩?zhàn)又杏袡C(jī)添加劑的溶解,如果添加劑不能充分溶解,或是溶解速度過慢,將影響膩?zhàn)优魏蟮某赡べ|(zhì)量和施工性能。施工環境過熱、過干也不行,膩?zhàn)邮┕みm宜在5℃-35℃的環境下進行。
The construction environment has always been a very important factor. If the ambient temperature is too low, it is easy to affect the dissolution of organic additives in the putty. If the additives cannot be fully dissolved or the dissolution rate is too slow, it will affect the film quality and construction performance of the putty after batching. The construction environment is neither too hot nor too dry. The putty construction should be carried out at 5 ℃ - 35 ℃.
![濟南膩?zhàn)臃? src=]()
4、膩?zhàn)优魏穸仍?.5mm-1mm之間
4. The thickness of putty is 0.5mm-1mm
膩?zhàn)拥呐尾荒芴∫膊荒芴瘛L〉脑挘佔訉尤菀资^快導致膩?zhàn)映霈F(xiàn)粉化,終會影響涂裝的效果。而膩?zhàn)訉优蔚迷胶瘢瑒t其干縮強度越大,越容易開裂。因此,單次膩?zhàn)拥呐魏穸群檬窃?.5mm-1mm之間。
The putty shall not be too thin or too thick. If the putty layer is too thin, it is easy to lose water too quickly, which will lead to putty pulverization, and will eventually affect the coating effect. The thicker the putty layer is scraped, the greater its dry shrinkage strength and the easier it is to crack. Therefore, the batch thickness of single putty is better between 0.5mm-1mm.
5、膩?zhàn)訑嚢韬梅胖脦追昼姡贁嚢枋褂?/div>
5. The putty shall be mixed and placed for several minutes before being used
在攪拌后放置一會兒,是為了給膩?zhàn)又械某煞痔峁┏浞秩芙獾臅r(shí)間以保證膩?zhàn)拥氖┕ば阅芎秃笃诔赡べ|(zhì)量,避免造成添加劑的浪費。膩?zhàn)釉谡{(diào)制成膏狀后,好在半小時內使用,以免膩?zhàn)幼冑|(zhì)影響施工效果。
Place it for a while after mixing to provide sufficient time for the ingredients in the putty to dissolve, so as to ensure the construction performance of the putty and the film quality in the later stage, and avoid the waste of additives. After the putty is mixed into a paste, it is better to use it within half an hour to avoid the deterioration of putty affecting the construction effect.
6、底層膩?zhàn)游锤赏覆坏米雒鎸?/div>
6. The bottom putty is not completely dry, and no surface course is allowed
內墻膩?zhàn)臃勰佔訉硬灰诉^厚,一定要等干透方可批二遍膩?zhàn)印6臼┕ぃ⒁夥纼鐾L(fēng)干燥,底層膩?zhàn)游锤赏覆坏米雒鎸印?/div>
The putty powder putty layer of the interior wall should not be too thick, and the putty can be applied twice only after it is completely dry. During winter construction, pay attention to antifreeze, ventilation and dryness, and do not make surface layer until the bottom putty is completely dry.
7、刮膩?zhàn)樱@些部位要貼布處理
7. Putty, these parts shall be treated with cloth
如果使用普通膩?zhàn)樱蚰退佔樱瑒t輕體墻、隔墻板之間接縫處、家具和墻面接縫處、墻面開槽處等部位好采用貼布處理工藝。如果使用彈性膩?zhàn)泳涂梢圆挥觅N布處理,直接批刮即可。
If ordinary putty or water-resistant putty is used, the joints between light wall and partition board, the joints between furniture and wall, and the wall grooving should be treated with cloth pasting. If elastic putty is used, it can be directly scraped without sticking cloth.
批刮膩?zhàn)硬粌H可以讓墻面更美觀,延長墻壁的壽命,還可以協助房間的防潮,注意以上事項,才能讓發揮膩?zhàn)拥淖饔茫尫课莸玫秸嬲谋Wo(hù)。關注我們帶
http://m.netjobs.cc你了解更多!
Applying putty can not only make the wall more beautiful and prolong the life of the wall, but also help the room to prevent moisture. Pay attention to the above items, so that the putty can play its role and the house can be truly protected. Follow us http://m.netjobs.cc You know more!