5. A layer of putty can survive only twice.

　　膩?zhàn)雍穸?.5 ~ 1.5mm。次刮膩?zhàn)訒r(shí)要找平時，膩?zhàn)雍穸?.5 ~ 0.8mm至均勻成型。膩?zhàn)雍穸燃s0.3 ~ 0.5mm。工藝以水平和垂直、力向均勻、覆蓋油脂達到勻光、不突然變輕和變重，以避免不同顏色、糊現象。表面膩?zhàn)討?yīng)在膩?zhàn)庸袒巴瓿伞５诙颖砻婺佔硬涣艉圹E，大面積表面光滑，光線方向自然，適合采光。膩?zhàn)哟闻c第二次之間的間隔時間和壓光時間應根據具體產品確定，并應服從制造商的指示。

　　Putty thickness is 0.5-1.5 mm. When scraping putty for the first time, the thickness of putty should be from 0.5 mm to 0.8 mm until it is evenly shaped. Putty thickness is about 0.3-0.5 mm. In order to avoid different color and paste phenomena, the technology uses horizontal and vertical, uniform force direction, uniform coverage of grease, no sudden lightening and weight change. Surface putty should be finished before putty curing. The second layer of putty does not leave traces, large area of smooth surface, natural light direction, suitable for lighting. The interval and calendering time between the first and the second time of putty shall be determined according to the specific product and shall be subject to the instructions of the manufacturer.

　　6、膩?zhàn)右螌?shí)輕壓實

　　6. Putty should be scraped and compacted

　　刮擦均勻，效果光滑，對于劃痕和不平，宜采用40 ~ 60目砂紙研磨。作為后的裝飾層的膩?zhàn)樱缬推嵩谶@個表面，應用水砂紙到啞光表面。

　　Scraping is even and the effect is smooth. For scratches and unevenness, 40 - 60 mesh sandpaper is suitable for grinding. Putty as the final decorative layer, such as paint on this surface, apply sandpaper to matte surface.

　　7. 打磨和拋光

　　7. Grinding and Polishing

　　第二次刮膩?zhàn)雍髴?yīng)及時除去裝飾線的橡膠條，清洗并修補邊角，用膩?zhàn)拥锻诙矗庩?yáng)角，裝飾線多余的膩?zhàn)隅P鏟，清洗干凈，達到線條清晰，無污染。凹面修補應先將水輥打濕，刮削修補處略高于原墻面，待完全干燥后，用細砂紙磨平抹平。

　　After scraping putty for the second time, the rubber strips of decorative lines should be removed in time, the edges and corners should be cleaned and repaired, the holes should be digged with putty knife, the Yin and Yang angles should be used, and the excess putty shovels and shovels of decorative lines should be cleaned, so that the lines are clear and pollution-free. Concave repair should first wet the water roller, scraping repair slightly higher than the original wall, to be completely dry, with fine sandpaper grinding flat.